Dialogic DSI SS7MD Manual de usuario Pagina 43
- Pagina / 176
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
43
Dialogic
®
DSI Signaling Server SGW Mode User Manual Issue 5
RDC1
First choice RDC for a continuous record
or periodic report
1 to 4
RDC2
Second choice RDC for a continuous
record or periodic report.
Zero indicates no RDC is assigned.
0 to 4 Default = 0
RECORD
The identifier for a continuous data
collection record
1 to 6
REPORT
The identifier for a periodic data
collection report
1 to 5
RESET Performs a reset operation Y or N Default = N
RESTART
Specifies the type of restart operation,
which can be one of the following:
• NORMAL - The system undergoes a
full system restart, resetting the
hardware, operating system and
signaling software. This is the
default behavior. NORMAL resets
should be used for software upgrade
or for maintenance events.
• SOFT - The system restarts the
application software. Prior to a soft
restart, the signaling boards are
reset. SOFT resets may be used for a
more rapid system restart after
updating the system configuration or
licenses. However, if a new software
distribution is to be installed, the
system performs a NORMAL restart.
• HALT - The system shuts down
without a subsequent restart.
Caution: Once the system has been
halted, the only way to restart the
unit is by physically pressing the
Power switch on the front panel of
the chassis.
One of:
•NORMAL
•SOFT
•HALT
SNMP object transition state.
One of:
•All
•Create
•Change
•Destroy
•None
Traps will be generated
if set to All, Create,
Change or Destroy.
Traps will not be
generated if set to
NONE.
Default = Change
RKI
Routing Key Index
An identifier for either a complete routing
key or part of a routing key.
1 to 512
RKTAB
Routing Key Table
A table of particular routing keys.
1 to 8
RTPRI Destination route priority
One of:
•NONE
•MTP
Default = NONE
RTS
A timeslot within a PCM interface on a
board used for monitoring information
received by the monitored object. The
format is:
xx-y-zz
where:
• xx = board position (BPOS)
• y = PCM within a board
• zz = timeslot
xx – 1 to 3
y – 1 to 4
zz – 1 to 31
SBITS Number of stop bits on V.24 port 1 to 2 Default = 1
SECURE
Secure operation. When active offers a
higher level of security. The use of the
parameter is command specific. See the
CNSYS and SNSLI command descriptions
for more information.
Y or N Default = N
Table 3. Parameter Definitions (Continued)
Name Description Range Notes
- Dialogic 1
- DSI Signaling Servers 1
- Copyright and Legal Notice 2
- Publication Date: August 2008 2
- Document Number: 05-2304-005 2
- Contents 3
- Revision History 8
- Chapter 1: Overview 9
- Chapter 1 Overview 10
- Chapter 2: Specification 17
- 2.3.2 Dialogic 19
- Chapter 2 Specification 20
- Chapter 4: Operation 27
- Chapter 4 Operation 28
- Are you sure? [Y/N] 29
- CNSYS:SECURE=Y; 31
- 5.3.2 MTP3-Specific Timers 47
- Table 6. MTP3 ITU Timers 47
- Table 7. MTP3 ANSI Timers 47
- ALCLS:CLA=,CODE=…; 50
- ALCLS:CLA=3,CODE=20; 50
- ALCLP[:CLA=]; 50
- CNMOI:C7LINK=,STS=,RTS=; 58
- CNMOE:C7LINK=; 58
- CNMOE:C7LINK=1; 58
- CNPCC:PCM=1-1,SYNCPRI=3; 62
- CNPCE:PCM=; 62
- CNPCE:PCM=1-1; 62
- • The RDC is blocked 64
- OFFSET value to take effect 70
- CNUSC:USER=3,AUTH=SHA; 75
- CNUSE:USER=; 75
- CNUSE:USER=3; 75
- CNXCI:OTS=,ITS=,[DUPLEX=]; 77
- CNXCE:OTS=,[DUPLEX=,]; 77
- CNXCE:OTS=1-1-16; 77
- C7LSE:LS=; 80
- C7LSE:LS=1; 80
- C7RTC:C7RT=1,NC=1,LS1=2; 82
- C7RTE:C7RT=,NC=; 82
- C7RTE:C7RT=1,NC=1; 82
- IPEPS:ETH=1,SPEED=100; 86
- IPEPS:ETH=4,IPADDR=STANDBY2; 86
- • MMPTP - MML Port Print 89
- • MMLOP - MML Log Off Print 89
- • MMLOS - MML Log Off Set 89
- • MMPTC - MML Port Change 89
- Attributes 91
- Examples 91
- Output Format 91
- Chapter 6 Command Definitions 100
- RDC1=1,LABEL=ALARM; 102
- RDCRE:RECORD=,[DISCARD=Y]; 103
- RDCRE:RECORD=1; 103
- SGDPI:DEST=1, RAS=1; 108
- SGDPI:DEST=,RTPRI=,[LABEL=,]; 108
- SGDPI:DEST=,RAS=,[LABEL=,]; 108
- SGDPC:DEST=1, RAS=1; 109
- SGDPE:DEST=; 109
- SGDPE:DEST=1; 109
- SGDPP:[DEST=]; 109
- SGIRC:IR=1,DEST=5; 111
- SGIRE:IR=; 111
- SGIRE:IR=1; 111
- SGIRP:[IR=]; 111
- SNALI:RAS=,SEQ=,SNLINK=; 114
- SNALI:RAS=1,SEQ=1,SNLINK=1; 114
- SNRAE:RAS=; 116
- SNRAE:RAS=1; 116
- IPADDR2=192.112.111.123;; 119
- SNSLC:SNLINK=1, PPORT=2905; 120
- SNSLE:SNLINK=; 120
- SNSLE:SNLINK=1; 120
- STIPP:IPADDR=173.132.23.3; 128
- IP Status 128
- EXECUTED 128
- • Status 133
- • Stratum 133
- • Offset 133
- 193.145.185.151 135
- 173.132.73.122 135
- 173.132.73.21 135
- 193.145.185.149 135
- Signaling 137
- 193.145.185.154 138
- SGDPI:DEST=2,RTPRI=MTP; 141
- • itself 143
- • an IP address of 0.0.0.0 143
- 194.192.185.11 145
- 192.195.185.11 145
- 192.195.185.12 145
- 194.192.185.12 145
- RESET=Y,LABEL=C7LINK; 158
- RDPDE:REPORT=1,C7LINK=3; 158
- 194.192.185.111 166
- 195.193.185.12 167
- 195.193.185.11 167
- 195.193.185.111 167
- 11.3.2 SG 2 Configuration 168
- STTPP command 169
- Chapter 13: Command Summary 171
- Chapter 13 Command Summary 172
- Glossary 175
- Chapter 14 Glossary 176
Relacionado con productos y manuales para Redes Dialogic DSI SS7MD
Redes Dialogic Mitel SX-2000 Especificaciones
(26 paginas)
(26 paginas)
Sony SVP132190X podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Notatniki Sony SVP132190X.
Dostarczamy 1 pdf podręczników Sony SVP132190X do pobrania za darmo według typów dokumentów: Specyfikacja Marketingowa
Comentarios a estos manuales