Dialogic DSI SS7MD Manual de usuario Pagina 100
- Pagina / 176
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
100
Chapter 6 Command Definitions
6.10.5 MSSLP – Measurements SIGTRAN Link Print
Synopsis
This command prints traffic measurements for SIGTRAN signaling links. The measurements are cumulative
between system startup and the next time the measurements are reset.
The fields have the following meanings:
• SNLINK - SIGTRAN signaling link
• RXCK - Number of data chunks received
• TXCK - Number of data chunks transmitted
• RTXCK - Number of data chunks re-transmitted
• NOOS - Number of times a SIGTRAN link has either been aborted or shutdown
• OSDUR - Duration that the link was not in service
• PERIOD - Time since measurements on the route were last reset. Specified in hours, minutes and
seconds
Syntax
MSSLP:[SNLINK =,][RESET=,];
Prerequisites
• If specified, the SIGTRAN signaling link must be an initiated and unblocked.
Attributes
None
Examples
MSSLP:SNLINK=1;
MSSLP;
Output Format
SIGTRAN Link Traffic Measurements
SNLINK RXCK TXCK RTXCK OSDUR NOOS PERIOD
1 54 6330 23 0 0 05:00:00
2 21 12 345 0 0 05:00:00
3 12 53 500 0 0 05:00:00
EXECUTED
6.10.6 MSSYP – Measurements System Print
Synopsis
This command prints out system related measurements for load and congestion taken over a period of time.
The fields in the output have the following meanings:
• NOVLD - The number of periods of congestion (overload) during the measurement period.
• MAXLOAD - Maximum load average measurement taken over one minute (based on the UNIX load
average).
• LOADAVG - The average load on the system (based on the UNIX load average) measurement taken over
the measurement period.
• PERIOD - The period the measurement was taken over.
Note: Values are reset using the RESET parameter. MSSYP:RESET=Y; resets the measurement values
to 0.
- Dialogic 1
- DSI Signaling Servers 1
- Copyright and Legal Notice 2
- Publication Date: August 2008 2
- Document Number: 05-2304-005 2
- Contents 3
- Revision History 8
- Chapter 1: Overview 9
- Chapter 1 Overview 10
- Chapter 2: Specification 17
- 2.3.2 Dialogic 19
- Chapter 2 Specification 20
- Chapter 4: Operation 27
- Chapter 4 Operation 28
- Are you sure? [Y/N] 29
- CNSYS:SECURE=Y; 31
- 5.3.2 MTP3-Specific Timers 47
- Table 6. MTP3 ITU Timers 47
- Table 7. MTP3 ANSI Timers 47
- ALCLS:CLA=,CODE=…; 50
- ALCLS:CLA=3,CODE=20; 50
- ALCLP[:CLA=]; 50
- CNMOI:C7LINK=,STS=,RTS=; 58
- CNMOE:C7LINK=; 58
- CNMOE:C7LINK=1; 58
- CNPCC:PCM=1-1,SYNCPRI=3; 62
- CNPCE:PCM=; 62
- CNPCE:PCM=1-1; 62
- • The RDC is blocked 64
- OFFSET value to take effect 70
- CNUSC:USER=3,AUTH=SHA; 75
- CNUSE:USER=; 75
- CNUSE:USER=3; 75
- CNXCI:OTS=,ITS=,[DUPLEX=]; 77
- CNXCE:OTS=,[DUPLEX=,]; 77
- CNXCE:OTS=1-1-16; 77
- C7LSE:LS=; 80
- C7LSE:LS=1; 80
- C7RTC:C7RT=1,NC=1,LS1=2; 82
- C7RTE:C7RT=,NC=; 82
- C7RTE:C7RT=1,NC=1; 82
- IPEPS:ETH=1,SPEED=100; 86
- IPEPS:ETH=4,IPADDR=STANDBY2; 86
- • MMPTP - MML Port Print 89
- • MMLOP - MML Log Off Print 89
- • MMLOS - MML Log Off Set 89
- • MMPTC - MML Port Change 89
- Attributes 91
- Examples 91
- Output Format 91
- Chapter 6 Command Definitions 100
- RDC1=1,LABEL=ALARM; 102
- RDCRE:RECORD=,[DISCARD=Y]; 103
- RDCRE:RECORD=1; 103
- SGDPI:DEST=1, RAS=1; 108
- SGDPI:DEST=,RTPRI=,[LABEL=,]; 108
- SGDPI:DEST=,RAS=,[LABEL=,]; 108
- SGDPC:DEST=1, RAS=1; 109
- SGDPE:DEST=; 109
- SGDPE:DEST=1; 109
- SGDPP:[DEST=]; 109
- SGIRC:IR=1,DEST=5; 111
- SGIRE:IR=; 111
- SGIRE:IR=1; 111
- SGIRP:[IR=]; 111
- SNALI:RAS=,SEQ=,SNLINK=; 114
- SNALI:RAS=1,SEQ=1,SNLINK=1; 114
- SNRAE:RAS=; 116
- SNRAE:RAS=1; 116
- IPADDR2=192.112.111.123;; 119
- SNSLC:SNLINK=1, PPORT=2905; 120
- SNSLE:SNLINK=; 120
- SNSLE:SNLINK=1; 120
- STIPP:IPADDR=173.132.23.3; 128
- IP Status 128
- EXECUTED 128
- • Status 133
- • Stratum 133
- • Offset 133
- 193.145.185.151 135
- 173.132.73.122 135
- 173.132.73.21 135
- 193.145.185.149 135
- Signaling 137
- 193.145.185.154 138
- SGDPI:DEST=2,RTPRI=MTP; 141
- • itself 143
- • an IP address of 0.0.0.0 143
- 194.192.185.11 145
- 192.195.185.11 145
- 192.195.185.12 145
- 194.192.185.12 145
- RESET=Y,LABEL=C7LINK; 158
- RDPDE:REPORT=1,C7LINK=3; 158
- 194.192.185.111 166
- 195.193.185.12 167
- 195.193.185.11 167
- 195.193.185.111 167
- 11.3.2 SG 2 Configuration 168
- STTPP command 169
- Chapter 13: Command Summary 171
- Chapter 13 Command Summary 172
- Glossary 175
- Chapter 14 Glossary 176
Relacionado con productos y manuales para Redes Dialogic DSI SS7MD
Redes Dialogic Mitel SX-2000 Especificaciones
(26 paginas)
(26 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.193 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales