Dialogic DSI SS7MD Manual de usuario descargar pdf (Pagina 40)

Chapter 5 Parameter Definitions

IPADDR

Internet Protocol (IP) address of the

Signaling Gateway Ethernet port 1

specified using dot notation, that is,

www.xxx.yyy.zzz

www – 0 to 255

xxx – 0 to 255

yyy – 0 to 255

zzz – 0 to 255

Default = 0.0.0.0

IPGW

Logical reference for an Internet Protocol

Gateway

DEFAULT or value 1 to 31

IPNW

IP network identifier specified using dot

notation, that is, www.xxx.yyy.zzz

www – 0 to 255

xxx – 0 to 255

yyy – 0 to 255

zzz – 0 to 255

Default = 0.0.0.0

IR Logical reference for a incoming route 1 to 32

ITS

The input timeslot in a cross connection

(in the case of a duplex cross connection,

this is also the output timeslot for the

reverse direction). The format is:

xx-y-zz

where:

• xx = board position (BPOS)

• y = PCM within a board

• zz = timeslot

xx – 1 to 3

y – 1 to 4

zz – 1 to 31

LABEL Text label.

0 to 12

LC PCM line coding

One of:

•HDB3

•AMI

•B8ZS

Default =

•HDB3 for E1

•B8ZS for T1

LINES Number of MML lines per page 10 to 99 Default = 25

LOCATION

Label identifying the location of the unit.

Max 24 characters.

LSH Load share across link sets Y to N Default = N

Logical reference of an SS7 link set,

which can contain a number of signaling

links

1 to 64

LS1

Primary link set associated with an SS7

route

1 to 64

LS2

Secondary linkset associated with an

SS7 route

1 to 64

LSSIZE

Maximum number of SS7 links allowed in

the link set. The link set size is used to

determine the load sharing algorithm

used across the link set.

1 to 16

M3UASHARE

The percentage of licensed throughput to

be allocated to the M3UA protocol.

Throughput capacity not allocated to

M3UA will be allocated to M2PA.

Blank (no value) or 1 to 99

After a change to the

M3UASHARE parameter,

the system should be

restarted so that the

change takes effect.

M56K

56kbits signaling mode:

• 0 - 64 kbits/s used

• 1 - 56kbits/s enabled (bit 8 not

used)

• 2 - 48kbits/s enabled (bits 7 and 8

not used)

• 3 - Recover clock from V.11 interface

• 4 - Transmit clock to V.11 interface

0 to 4

Default = 0

M56K modes 3 and 4

can only be set on

boards with SIGTYPE =

SS7

For framed HSL, the

valid M56K modes are

0(64k), 1(56k) and

2(48k). These values

are used to identify the

data rate, which is

applied to all timeslots

on the link. For

unstructured HSL links,

the M56K parameter

must be set to 0.

Table 3. Parameter Definitions (Continued)

Name Description Range Notes

1 2 ... 35 36 37 38 39 40 41 42 43 44 45 ... 175 176

Comentarios a estos manuales

Sin comentarios

Dialogic DSI SS7MD Manual de usuario Pagina 40

Comentarios a estos manuales

Relacionado con productos y manuales para Redes Dialogic DSI SS7MD