Dialogic SS7G2X Manual de usuario Pagina 35
- Pagina / 170
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
35
Dialogic
®
SS7G2x Signaling Server SGW Mode User Manual Issue 4
RESTART
Specifies the type of restart operation,
which can be one of the following:
• NORMAL - The system undergoes a full
system restart, resetting the hardware,
operating system and SIU software.
This is the default behavior. NORMAL
resets should be used for software
upgrade or for maintenance events.
• SOFT - The system restarts the
application software. Prior to a soft
restart, the Signaling boards are reset.
SOFT resets may be used for a more
rapid system restart after updating the
system configuration or licenses.
However, if a new software distribution
is to be installed, the system performs
a NORMAL restart.
• HALT - The system shuts down without
a subsequent restart.
Caution: Once the system has been
halted, the only way to restart the unit
is by physically pressing the Power
switch on the front panel of the
chassis.
One of:
•NORMAL
•SOFT
•HALT
RKI
Routing Key Index
An identifier for either a complete routing
key or part of a routing key.
1 to 512
RKTAB
Routing Key Table
A table of particular routing keys.
1 to 8
RTPRI Destination route priority
One of:
•NONE
•MTP
Default = NONE
RTS
A timeslot within a PCM interface on a board
used for monitoring information received by
the monitored object. The format is:
xx-y-zz
where:
• xx = board position (BPOS)
• y = PCM within a board
• zz = timeslot
xx – 1 to 3
y – 1 to 4
zz – 1 to 31
SBITS Number of stop bits on V.24 port 1 to 2 Default = 1
SECURE
Secure operation. When active offers a
higher level of security. The use of the
parameter is command specific. See the
CNSYS and SNSLI command descriptions
for more information.
Y or N Default = N
SEQ Sequence number 1 to 32
SG Reserved
SI Reserved
SIGTYPE
Type of software loaded onto signaling
board
SS7
SLC
Signaling link code uniquely identifying a
signaling link within a link set
0 to 15
SNMP
Whether SNMP should be active on the
system
Y or N Default = N
SNRT Reserved
SNTYPE The type of operation of the SIGTRAN link
One of:
•SGM3UA
•M2PA
SNLINK Logical reference for a SIGTRAN link 1 to 200
Table 2. Parameter Definitions (Continued)
Name Description Range Notes
- Dialogic 1
- SS7G2x Signaling Server 1
- Document Number: 05-2304-004 2
- Contents 3
- Revision History 7
- • Dialogic 8
- Chapter 1 Overview 10
- Chapter 2: Specification 15
- #!/bin/sh 19
- Chapter 4: Operation 20
- Are you sure? [Y/N] 22
- EXECUTED 22
- CNSYS:SECURE=Y; 23
- Chapter 4 Operation 24
- 5.2 Remote Operations 37
- ALREI[:ALP=]; 46
- ALREI:ALP=100; 46
- ALTEI:CLA=3; 46
- CNMOI:C7LINK=,STS=,RTS=; 51
- CNMOE:C7LINK=; 51
- CNMOE:C7LINK=1; 51
- CNPCC:PCM=1-1,SYNCPRI=3; 53
- CNPCE:PCM=; 53
- CNPCE:PCM=1-1; 53
- CNRDE:RDC=; 55
- CNRDE:RDC=1; 55
- CNXCI:OTS=,ITS=,[DUPLEX=]; 64
- CNXCE:OTS=,[DUPLEX=,]; 64
- CNXCE:OTS=1-1-16; 64
- C7RTC:C7RT=1,NC=1,LS1=2; 71
- IPNW=128.66.1.0; 78
- IPGWE:IPGW=; 78
- IPGWE:IPGW=1,; 78
- • MMLOP - MML Log Off Print 80
- • MMLOS - MML Log Off Set 80
- • MMPTC - MML Port Change 80
- • MMPTP - MML Port Print 80
- MNRSI:RESET=Y; 88
- MNRSI:SYSTYPE=SGW; 88
- MSC7P:C7LINK=1; 90
- Output Format 91
- MSEPP:[RESET=,][PAGE=,]; 92
- MSEPP:RESET=YES,PAGE=2; 92
- RDC1=1,LABEL=ALARM; 98
- Chapter 6 Command Definitions 100
- RDPDE:REPORT=1,C7LINK=1; 101
- RDPRE:REPORT=; 104
- RDPRE:REPORT=1; 104
- SGDPI:DEST=1, AS=1; 107
- SGDPC:DEST=1, AS=1; 107
- SGDPI:DEST=,RTPRI=,[LABEL=,]; 107
- SGDPI:DEST=,AS=,[LABEL=,]; 107
- SGIRI:IR=1, DOMAIN=IP,RKI=1; 109
- SGIRC:IR=1,DEST=5; 110
- SGIRE:IR=; 110
- SGIRE:IR=1; 110
- SNALI:AS=,SEQ=,SNLINK=; 115
- SNALI:AS=1,SEQ=1,SNLINK=1; 115
- SNALE:AS=,SEQ=; 115
- SNNAI:NC=,SNLINK=,SS7MD=,NA=; 118
- SNNAE:SNLINK=,NC=; 118
- SNNAE:SNLINK=1,NC=1; 118
- IPADDR2=192.112.111.123;; 120
- SNSLC:SNLINK=1, PPORT=2905; 121
- SNSLE:SNLINK=; 121
- SNSLE:SNLINK=1; 121
- 193.145.185.151 135
- 173.132.73.122 135
- 173.132.73.21 135
- 193.145.185.149 135
- Signaling 137
- 193.145.185.154 138
- SGDPI:DEST=1,RTPRI=NONE,AS=1; 140
- SGDPI:DEST=2,RTPRI=MTP; 140
- • itself 142
- • an IP address of 0.0.0.0 142
- 194.192.185.11 144
- 192.195.185.11 144
- 192.195.185.12 144
- 194.192.185.12 144
- Chapter 10: SS7G2x SNMP MIB 158
- 193.145.185.152 160
- 193.145.185.153 160
- 194.192.185.111 161
- 195.193.185.12 161
- 195.193.185.11 161
- 195.193.185.111 161
- Chapter 12: Command Summary 163
- Chapter 12 Command Summary 164
- Glossary 166
- SEP Signaling End Point 167
Relacionado con productos y manuales para Gateways / Controladores Dialogic SS7G2X
(6 paginas)Sony SVP112190X podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Notatniki Sony SVP112190X.
Dostarczamy 1 pdf podręczników Sony SVP112190X do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comentarios a estos manuales