Dialogic DSI SPCI Network Interface Boards Manual de usuario Pagina 101
- Pagina / 111
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Dialogic
®
DSI SPCI Network Interface Boards Programmer's Manual Issue 5
101
a) The only link set used to reach the destination.
b) The preferred link set used to reach the destination.
c) One of a pair of links sets forming a combined link set.
In the latter two cases a second link set (second_ls) must also be specified.
Within a link set messages are automatically load-shared across links using
the Signaling Link Selection (SLS) field in the message.
<second_ls>
The linkset_id of an optional second link set used to reach the specified
destination. This may be either of the following options:
a) The secondary link set used to reach the destination only on failure of the
preferred link set.
b) One of a pair of links sets forming a combined link set over which load-
sharing takes place. (in this case bit 1 must also be set in the <flags>
parameter of the command).
When a second link set is specified the user must also set bit 0 in the
<flags> field of this command.
<user_part_mask>
This is a 16 bit field used identify the user parts that are supported over this
route. The bits are labelled 0 to 15 and for each user part supported the bit
corresponding to the Service Indicator for that user part must be set. (e.g.,
To support just ISUP messages, the ISUP Service Indicator is 5 so bit 5
should be set. Therefore a value of 0x0020 would be appropriate).
<flags>
A 16 bit field containing run-time configuration options for the route as
follows:
Bit 0 is set to 1 to indicate that a second link set is specified within the
command. If zero the second_ls parameter is ignored.
Bit 1 is used to determine whether or not to load-share messages across the
two link sets. It is only used when two link sets are specified for the route.
When set the MTP3 module load-shares messages for the destination equally
across each of the two specified link sets. Otherwise the MTP3 module
considers the normal link set to be the preferred link set and only uses the
second link set in the event of failure of the normal link set. The bit may be
set to 1 to enable load-sharing across the two link sets, or zero to disable
load-sharing and use preferred and secondary link sets.
All other bits are reserved for future use and must be set to zero.
- Dialogic 1
- Copyright and Legal Notice 2
- Contents 3
- Tables 5
- Revision History 6
- 1 Introduction 7
- 2 Specification 8
- 2.3.2 Capacity 9
- 3 Installation 10
- 3.2 Hardware configuration 11
- 3.3.2 Starting the Windows 12
- Device Driver 12
- 3.3.3 Clearing Windows 13
- 2000 Install Wizard 13
- 3 Installation 14
- 4.1 Overview 19
- 4.2 System Configuration 21
- 4.3 Protocol Configuration 24
- 4.5 Geographic Addressing 27
- 4.6 Watchdog Timer 27
- 4.7 Using the CT bus 27
- 4.7.1 Switching Model 28
- 4.7.2 Static Initialization 28
- 4.7.3 Dynamic Operation 29
- 5 Program Execution 32
- –x parameter: 34
- 6 Message Reference 36
- 6.1.5 Message Summary Table 37
- 6 Message Reference 38
- 6.2.1 SSD Reset Request 39
- 6.2.2 Board Reset Request 40
- Value Description 48
- Parameter Description: 51
- Value Mnemonic Description 52
- Synopsis: 53
- Interface Unit (LIU) 53
- Message Format: 53
- 6.3.2 LIU Control Request 57
- 6.3.5 LIU State Request 61
- 0xff None Setup failed 64
- 6.3.7 CT bus Listen Request 65
- 6.3.9 Reset Switch Request 68
- 4 Mbps 0 ... 63 72
- 8 Mbps 0 … 128 72
- Board Status 80
- 6.4.4 LIU Status Indication 83
- 6.4.5 Error Indication 84
- Error Code 85
- 7.1.1 SS7_BOARD Command 91
- 7.1.2 LIU_CONFIG Command 93
- 7.1.3 LIU_SC_DRIVE Command 95
- 7.1.4 SCBUS_LISTEN Command 96
- 7.2 MTP Parameters 97
- 7.2.2 MTP Link Set 98
- 7.2.3 MTP Signaling Link 98
- 7.2.4 MTP Route 100
- 7.3 ISUP Parameters 102
- 7.4 TUP Parameters 105
- 8 Host Utilities 108
- 8.2 s7_mgt 109
- 8.2.4 Example 110
Relacionado con productos y manuales para Software Dialogic DSI SPCI Network Interface Boards
Software Dialogic Diva Pro PC Manual de servicio
(66 paginas)
(66 paginas)
Software Dialogic Diva ISDN USB Manual de servicio
(69 paginas)
(69 paginas)
Dual-electronics Wzmacniacz samochodowy podręczniki użytkownika
Zaczynanie od D
Comentarios a estos manuales